Removing the standard radio from Nissan Almera G15 (2013–2022 model years) - a task that may be needed when upgrading an audio system, repairing or diagnosing electronics. Despite its apparent simplicity, the process has a number of hidden nuances: from unobvious fasteners to the risk of damaging the plastic panel clips. In this article we will analyze three official dismantling methods (with keys, without keys and through the bottom of the console), and we will also tell you how to avoid mistakes that lead to broken wiring or broken latches of ISO connectors.

Important: the design of the radio is Almera G15 depends on the configuration. In basic versions (for example, Visia) a standard 1DIN system with mechanical locks is used, and in top-end (Acenta or Tekna) - double-din multimedia with additional mounts for climate control. We cover both options.

Preparation: Tools and Safety Precautions

Before starting work, make sure you have everything you need. The absence of even one tool can lead to irreversible damage plastic interior parts. Here is the minimum set:

  • 🔧 Plastic mounting blades (2–3 pcs.) - for dismantling the panel without scratches.
  • 🔑 Keys for removing the radio (if any) - universal fit DIN keys or original Nissan (article 28510-4M000).
  • 🔌 Screwdriver TORX T20 — for unscrewing the screws of the lower console (in some configurations).
  • 📸 Smartphone - to photograph the connectors before disconnecting (this will save you from confusion during reassembly).
  • 🧲 Magnetic holder - for convenient storage of small screws.

⚠️ Attention: If your Almera G15 equipped with a system NissanConnect (with navigation), before removing the radio necessarily remove the memory card from the slot. Otherwise, the contacts may bend during dismantling.

📊 What experience do you have with auto electronics?
  • I'm removing the radio for the first time
  • Already changed it before, but not on Nissan
  • I am a professional car audio professional.
  • I prefer to contact the service

Also prepare your workspace:

  • 🚗 Park the car on a flat surface and turn off the ignition (key to position LOCK).
  • 🔋 Remove the negative terminal from the battery - this will prevent a short circuit when working with wires.
  • 🌡️ If it’s cold outside (below +10°C), warm up the interior - plastic becomes fragile in the cold.

Method 1: Removing the radio using keys (for 1DIN systems)

This method is suitable for basic configurations Almera G15 with single-din radio (without screen). The main advantage is the minimal risk of damage to the panel, since there is no need to disassemble the console.

Algorithm of actions:

  1. Paste two DIN keys into the side grooves of the radio (they are located under the volume controls). If there are no keys, you can use curved paper clips 1.5–2 mm thick.
  2. Press down on the keys simultaneously and evenlyuntil you hear a click - this means that the latches are disengaged.
  3. Gently pull the radio towards you. If it does not budge, check whether all the latches are latched (sometimes you need to pry the bottom part with a spatula).
  4. Disconnect the connectors: first ISO power connector (black), then antenna cable (blue).

The latches are completely released|All connectors are disconnected (power + antenna)|No wires are pinched behind the case|Photo of the connectors is taken-->

⚠️ Attention: In some batches Almera G15 (2014–2016) used additional mounting screws under the decorative trim. If the radio does not come out even after clicking, check for their presence - they may be hidden under a sticker with the serial number.

Radio type Number of clamps Additional mounts Connectors
1DIN (basic) 4 (2 on each side) No ISO + antenna
1DIN (with USB) 4 1 screw under cover ISO + antenna + USB
2DIN (NissanConnect) 6 (4 side + 2 top) 2 screws for climate control ISO + antenna + CAN bus + camera

Method 2: Dismantling without keys (alternative method)

If there are no keys for removal, and the radio does not come out after pressing the latches, you can use plastic spatulas. This method requires caution, as there is a risk of damaging the front panel.

Step by step instructions:

  1. Insert a spudger into the gap between the radio and the panel on the right side (passenger side). Here the plastic is thinner and the risk of damage is minimal.
  2. Tilt the paddle at a 30° angle and push down until you feel the latch give way. Repeat the same on the left side.
  3. After snapping the two upper latches, pull the radio towards you, holding the lower part - there may be additional latches there.
💡

If the radio is “jammed” and won’t come out, try shaking it slightly left and right. This often helps free up jammed fasteners.

⚠️ Attention: Do not use metal screwdrivers or knives - they will leave scratches on the plastic and may short out the contacts on the back of the radio. If the blade does not fit into the gap, then the radio is secured with screws (see. Method 3).

After removal, inspect the housing for cracks. B Almera G15 2017–2022 models are sometimes found with radios with fragile plastic guides - They are easy to break with excessive force.

Method 3: Complete dismantling of the center console (for 2DIN systems)

This method is necessary for removing multimedia systems NissanConnect or touch screen radio. Here you will need to disassemble part of the dashboard, which takes more time, but guarantees the safety of all fastenings.

Procedure:

  1. Remove climate control decorative trim:
    • Use a spatula to pry up the lower edge of the trim (from the gearshift lever side).
    • Snap off the 4 plastic clips (2 on top, 2 on bottom).
    • Disconnect the backlight connector (white connector).
  2. Unscrew two TORX T20 screwsholding the radio from above (they are hidden under the cover).
  3. Pull the radio towards you, having first turned it off:
    • Main ISO connector (black).
    • Connector CAN buses (orange, only for systems with navigation).
    • Rear camera cable (yellow, if available).
What to do if the screws won't come off?

If TORX screws are stuck or won't budge, try the following methods:

1. Use rubber band between the screwdriver and the screw for better grip.

2. Heat the screw with a hair dryer (not higher than 60°C) - this will expand the metal.

3. As a last resort, drill out the screw with a 3mm drill bit, but be careful not to damage the threads in the plastic.

⚠️ Attention: In radios with Apple CarPlay/Android Auto (installed since 2019) there is an additional microphone jack (gray, located at the back left). It is easy to miss, and sudden movement can tear off the wires.

Common mistakes and how to avoid them

Even experienced car owners make mistakes when removing the radio. Here are the most common ones and ways to prevent them:

  • 🔌 Broken antenna wires - happens if you pull the radio by the cable. Solution: always disconnect the connectors after complete removal of the housing.
  • 🔧 Loss of retainers — small plastic latches fall out during careless dismantling. Solution: work over a table with a cloth underneath.
  • 📱 Resetting the radio settings — if you do not disconnect the battery, the radio station memory may be erased. Solution: use a backup power source (for example, Power Bank with adapter for cigarette lighter).
  • 🔊 Damage to speakers - in case of a short circuit while disconnecting the connectors. Solution: check the circuit with a multimeter before connecting a new radio.
💡

If, after installing a new radio, the buttons on the steering wheel stop working, the problem is CAN bus incompatibility. The solution is to use an adapter PAC RP4-NIS01 or similar.

Pay special attention power connector. B Almera G15 non-standard pinout is used ISO connector, where:

  • Yellow wire — constant plus (+12V).
  • Red wire — plus from ignition (ACC).
  • Black wire — mass (minus).
  • Blue/White Wire — antenna or amplifier (if available).

Installing a new radio: compatibility and connection

If you are removing the radio for replacement, consider the following points:

Size Compatibility:

  • For 1DIN systems any standard radio is suitable 180×50 mm.
  • For 2DIN (with screen) size needed 180×100 mm, but check the depth - in some trim levels the climate control unit gets in the way.

Connection adapters:

  • 🔌 ISO adapter - if the new radio has a different power connector (for example, Pioneer or Sony).
  • 📞 CAN bus adapter — to preserve the operation of the buttons on the steering wheel and the on-board computer display.
  • 🎵 Antenna amplifier - if the signal from radio stations has become worse (in Almera G15 active antenna is used).

⚠️ Attention: When connecting a radio with Android Auto or CarPlay The head unit firmware may need to be updated. Otherwise possible freezing or no sound on phone calls.

💡

Before purchasing a new radio, check its compatibility with the CAN bus Nissan on the manufacturer's website. For example, models Pioneer SPH-DA130DAB And Sony XAV-AX5000 work without adapters.

Frequently asked questions after removing the radio

Is it possible to remove the radio without disconnecting the battery?

Technically yes, but this risky. A short circuit may cause the fuse to burn out. F30 (10A) in the fuse box (located under the steering wheel). If you are an experienced auto electrician, you can do without disconnecting, but for beginners it is better not to risk it.

Why don't the speakers work after installing a new radio?

The reasons may be as follows:

  1. Incorrect pinout of connectors (check plus/minus on the speakers).
  2. There is no signal from the amplifier (in Almera G15 it can be submitted separately).
  3. The new radio requires setting the output voltage (go to Settings → Sound → Output Level).

How to remove the radio if the latches are broken?

If the plastic latches break off, there are two options:

  1. Use metal staples (can be made from paper clips) that will hold the radio instead of clamps.
  2. Install the radio in fake frame (sold for Nissan under the article 28510-4M010).

Where is the radio fuse located in Almera G15?

The audio system fuse is located in interior fuse box (under the steering wheel, on the left). This is a fuse F30 (10A) with the inscription AUDIO. Also check F20 (7.5A) — he is responsible for the button illumination.

Is it possible to connect a rear view camera to the standard radio?

Yes, but only if the radio supports video input. B Almera G15 with NissanConnect for this you need:

  • Camera with connector RCA.
  • Adapter for connecting to the rear camera connector (article no. 28510-4M020).
  • Software activation of the function in the menu (firmware may be required).