How to properly remove wipers on a Nissan Qashqai: instructions with photos and videos

Replacing wipers with Nissan Qashqai - a procedure that every crossover owner faces sooner or later. Even if you have never held a screwdriver in your hands, you can complete the task in 10–15 minutes if you know a few key nuances. In this article we will look at step-by-step algorithm for removing wipers for all generations Qashqai (J10, J11, J12), we will point out typical mistakes and give recommendations for choosing new brushes.

Features of the design of mounting wipers on Nissan is to use hook type latch or side pin - depending on the year of manufacture. Improper handling of the mechanism can lead to breakage of the plastic adapter or even damage the windshield wiper drive. To avoid unnecessary expenses, just follow the proven instructions and use the tools at hand.

Preparing to remove wipers: tools and safety precautions

Before you begin dismantling, make sure you have everything you need on hand. For most models Qashqai The minimum set is enough:

• 🔧 Flat head screwdriver (to pry up the latch if your hand can’t handle it).
• 🧤 Gloves (will protect your hands from dirt and sharp edges of the metal fastening).
• 📏 Ruler or tape measure (to measure the length of the brushes before purchasing new ones).
• 🧴 WD-40 or silicone grease (if the fastening has soured or become stuck).

Important: on models Qashqai 2014-2021 (J11) often uses a side pin mount that requires gentle pressure on the latch from below. On older J10s (2007–2013) there is a classic “hook”, which is easier to remove without tools. If you are unsure of the type of attachment, look under the plastic cap at the base of the wiper.

⚠️ Attention: Never use force if the wiper does not budge! A stuck mount can be damaged, and replacing the windshield wiper drive will cost 5–8 thousand rubles. It is better to treat the connection with WD-40 and wait 10-15 minutes.

Also before work turn off the ignition and make sure that the wipers are in the down position (the switch lever is in the position OFF). If the brushes stop at the top point, turn on the ignition for a second and turn it off - they will return to their original position.

Types of wiper mounts on Nissan Qashqai: how to determine yours?

On Nissan Qashqai There are three main types of windshield wiper blade mounts. The removal algorithm depends on the type:

Mounting type	Years of manufacture	Features	Photo/diagram
Hook	2007–2013 (J10)	Classic U-shaped clamp. It can be removed by pressing the tab on top.	📷
Side Pin	2014–2021 (J11)	The latch is located on the side. Requires pressing a button on the bottom or side.	📷
Push Button	2021–present time (J12)	Locking button on top. It can be removed by pressing and sliding the brush upward.	📷

To accurately determine the type of mount on your Qashqai, follow these steps:

1. Lift the plastic cap at the base of the wiper (if equipped).
2. Inspect the metal adapter: if a tab is visible at the top, this is Hook; if the button is on the side - Side Pin; if the button is on top - Push Button.
3. For Qashqai J12 (after 2021) characteristic fastening Push Button with a plastic cover that can be removed by moving upwards.

If you buy new brushes, pay attention to the fastening markings on the packaging. For example, for Side Pin brushes with markings are suitable SP22 or Side Lock, and for Hook — U-Hook 9x3 or 9x4.

Step-by-step instructions: how to remove wipers on a Nissan Qashqai J10 (2007–2013)

First generation models (Qashqai J10) were equipped with a fastening type Hook - the easiest to maintain. To remove the brushes you don’t need a tool, just follow the algorithm:

Step 1. Raise the wiper arm perpendicular to the windshield (toward position). Make sure it locks in this position.

Step 2. Press the plastic release tab (located on top of the mount) and hold it. The tongue should snap off with a characteristic sound.

Step 3. Gently slide the brush down along the lever, removing it from the metal hook. If the brush does not give way, do not pull it by force - check whether the latch is completely released.

Step 4. Repeat the procedure for the second wiper. Please note: on Qashqai J10 left and right brushes may differ in length (usually 60 cm and 40 cm).

⚠️ Attention: On some restyled versions of the J10 (after 2010) there is a mount Side Pin. If there is no tab on top, look for the button on the side - the removal algorithm will be different (see the next section).

After removal, inspect the metal arm for corrosion. If rust is present, clean it with fine sandpaper and treat it with silicone grease - this will extend the life of the new fastener.

Removing wipers on Nissan Qashqai J11 (2014–2021): Side Pin fastening

Second generation Qashqai received a more reliable, but also more capricious fastening Side Pin. The main difficulty is that the latch is hidden under a plastic cap and is not always visible at first glance. Let's look at the process step by step:

Step 1. Raise the wiper arm to the vertical position. On J11 the levers are more rigid, so force may be required.

Step 2. Remove the plastic cap at the base of the brush by pulling it up. Below it you will see a metal adapter with a side button.

Step 3. Press the release button (it can be located on the side or bottom) and hold it. At the same time, pull the brush down, removing it from the lever.

If the button is not pressed:

• 🔧 Try processing the connection WD-40 and wait 5–10 minutes.
• 🧲 Use a flathead screwdriver to carefully pry the button (but do not use excessive force!).
• 📸 Take a photo of the mount and check the instructions for the new brushes - perhaps you are pressing the wrong button.

On Qashqai J11 after 2017, a modified mount is sometimes found Side Pin with double lock. In this case, you need to press two buttons at once (on the side and bottom) or use a special key from the set of new brushes.

What to do if the release button is broken?

If the plastic button breaks off, do not try to remove the brush by force - this may damage the lever. In this case, carefully drill a hole in the adapter (2-3 mm) and use a self-tapping screw to pull out the brush. After replacing the adapter (cost ~300–500 rubles), the problem will be solved.

Features of removing wipers on Nissan Qashqai J12 (2021–present)

Third generation Qashqai returned to a simplified type mount Push Button, but with some nuances. The main difference is the presence of a plastic cover, which is removed by moving upwards and not sideways.

Algorithm for J12:

1. Raise the wiper arm to the vertical position.
2. Slide the plastic cover up (it is secured with latches).
3. Press the lock button on top and pull the brush towards you.

On Qashqai J12 often installed frameless brusheswhich require more careful handling. When removing, do not pull on the rubber part - only grasp the plastic adapter!

Also note brush length:

• 📏 Driver's side: 650–670 mm.
• 📏 Passenger side: 400–420 mm.

⚠️ Attention: On some versions of J12 with the option Intelligent Auto Headlights wipers can be equipped with a rain sensor. In this case, when removing the brushes do not touch the sensor wire — it goes inside the lever.

Common mistakes when removing wipers and how to avoid them

Even experienced car owners sometimes make mistakes that lead to damage to fasteners or levers. Let's look at the most common ones:

1. Application of force to a lever. If the brush cannot be removed, do not pull it “with meat” - this can bend the metal lever or break the plastic adapter. Always check that the latch is released.
2. Ignoring the plastic cap. On J11 And J12 The cap hides the retainer. If you don't remove it, you'll be pushing in the wrong place.
3. Mismatch of fastening types. When purchasing new brushes, make sure that their adapter is compatible with yours. Qashqai. For example, brushes for Hook will not fit Side Pin.
4. They forget to note the position of the levers. If you accidentally turn on the windshield wipers without blades, the arms may hit the windshield and damage it. Always return the levers to the down position after removal.

Another common problem is fastening sticking. This occurs due to corrosion or prolonged use without replacement. To avoid this:

• 🧴 Treat the fastening every 3-4 months silicone grease.
• 🚿 Wash your wipers not only outside, but also rinse the mounting area with water (especially in winter, after treating roads with reagents).
• ❄️ In winter, before parking, raise the wipers to a vertical position - this will prevent the blades from freezing to the glass.

If you do break the latch, don't despair. Adapters for mounts are sold separately (cost from 200 to 800 rubles) and are replaced in 5 minutes.

How to install new wipers: nuances for Nissan Qashqai

Installing new brushes is the reverse process of removing them, but with a few important points. Here is a step-by-step algorithm:

Step 1. Compare the new brushes with the old ones in terms of length and type of fastening. Even if the packaging promises compatibility with Qashqai, better double check.

Step 2. Place the brush on the lever until you hear a characteristic click. For Side Pin You may need to press the release button to Push Button - simple pressure until you hear a click.

Step 3. Make sure that the brush is firmly fixed: pull it down - it should not move. If the fixation is not secure, check whether the adapter is seated correctly.

Step 4. Lower the lever onto the glass and turn on the wipers at minimum speed to check operation. Please note:

• 🔊 There should be no extraneous sounds (creaks, knocks).
• 💧 The brushes should fit tightly to the glass along the entire length.
• 🌀 The water should be evenly driven to the sides, without streaks.

If the new blades leave streaks, they may be too hard for your glass. In this case try silicone brushes or models with graphite coating.

FAQ: Frequently asked questions about replacing wipers on a Nissan Qashqai

Is it possible to remove the wipers without tools?

Yes, on most models Qashqai (especially J10 and J12) the brushes are removed manually. The exception is stuck or corroded fasteners, where a screwdriver or WD-40 may be needed.

What size wipers fit my Qashqai?

Depends on generation:

• J10 (2007–2013): 600 mm (driver) / 400 mm (passenger).
• J11 (2014–2021): 650 mm / 420 mm.
• J12 (2021–present): 670 mm / 400 mm.

For accuracy, measure the old brushes with a tape measure.

What to do if after replacement the wipers work jerkily?

The reasons may be as follows:

• The brushes are not installed correctly (check the fixation).
• The wiper arms are bent (need to be straightened or replaced).
• The windshield wiper drive is worn out (diagnostics required).

First, make sure that the brushes are properly secured and do not catch on the edge of the glass.

Is it possible to wash a car without wipers?

Yes, but with caution:

• Do not direct high pressure water jets at exposed fasteners.
• Avoid automatic car washes with brushes - they can damage the arms.
• After washing, dry the fasteners to prevent corrosion.

How much do original wipers for Qashqai cost?

Prices for original brushes Nissan (article 28650-JM00A for J11):

• 💰 Front: RUB 1,200–1,800 per set.
• 💰 Rear: 800–1,200 rub.

Analogs (for example, Bosch Aerotwin or Denso) will cost 800–1,500 rubles. per set.