Time on the dashboard Nissan Juke - it would seem a trifle, but it is precisely this that can ruin the mood with a broken alarm clock or incorrect marks in the logbook. This is especially true for model owners 2010–2019, where automatic synchronization often malfunctions. In new versions (2020+), the system has become smarter, but there are also nuances there - for example, after replacing the battery or updating multimedia firmware.

In this article we will analyze all ways to set the time - from basic adjustments through the menu to solving “glitches” with the clock after repair. Let us dwell separately on Juke with the system NissanConnect and analog devices, where the algorithms differ. And if you are faced with the fact that the time gets lost every day, we have a unique solution that bypasses a factory bug in the 2018 firmware.

1. Preparation: what you need to know before setting up

Before you get into the settings, check three key points:

  • 🔋 Battery charge. If the voltage is lower 12.4V, the clock may get lost even after manual adjustment. Measure with a multimeter or pay attention to the dim light on the instrument panel when starting.
  • 📡 GPS/GLONASS signal. In models with NissanConnect (2017+) time is synchronized by satellites. If the antenna is damaged (for example, after a pressure wash), automatic adjustment will not work.
  • 🔧 Firmware version. B Juke In 2015–2016, there was a bug due to which the clock was lost at temperatures below -10°C. Upgrade to version 1.04.02 solves the problem.

If you have recently changed the battery, wait complete initialization of the computer (usually takes 10-15 minutes after the first launch). During this period, the system can ignore manual time settings. Also make sure that in the car Power saving mode is turned off (ECO Mode), which sometimes blocks background synchronization processes.

⚠️ Attention: B Nissan Juke 2011–2013 with analog instrumentation there is no separate menu for the clock — time is adjusted only through the multimedia system. If you have this version, skip the section about settings on the device and see the instructions for the screen.

2. Setting the time via the dashboard (2014–2026)

In models with digital instrumentation (TFT display) the algorithm is simple:

  1. Press and hold the button TRIP (to the right of the speedometer) on 3 secondsuntil the menu appears.
  2. Buttons ↑/↓ select item on the steering wheel Clock Adjust (or Time Setting in European versions).
  3. Click OK (central button on the steering wheel) and set the hours/minutes using the buttons +/–.
  4. Hold to save OK 2 seconds - the message appears on the screen Saved.

B Juke 2020+ with system ProPILOT the clock menu is hidden deeper: you need to go to Vehicle Settings → Display → Clock. The option is also available here Auto Sync (automatic GPS synchronization), but it only works when actively connected to NissanConnect Services (requires SIM card).

Check battery charge (minimum 12.4V)

Make sure the machine is not in ECO Mode

Turn off Bluetooth (sometimes interferes with syncing)

Remember the current time for comparison after setting-->

If after saving the time is still lost, try reset dashboard settings:

1. Выключите зажигание.

2. Зажмите кнопку сброса суточного пробега (TRIP).


3. Включите зажигание (не запуская двигатель).


4. Удерживайте кнопку 10 секунд, пока дисплей не мигнёт.

3. Setup via the multimedia system (all generations)

B Nissan Juke with the system NissanConnect (or old CD/MP3- radio) the clock is adjusted through the screen:

  • 📻 Click the button SETUP on the radio (or MENU in new versions).
  • ⚙️ Select Clock → Manual Adjust.
  • 🕒 Set time using buttons <</>> (for watches) and ▲/▼ (for minutes).
  • 💾 Save by pressing OK or ENTER.

In radios with Android Auto/Apple CarPlay (optional NAVI) time can be synchronized from the smartphone automatically. To disable this feature:

  1. Go to Settings → System → Date & Time.
  2. Disable Automatic Date & Time.
  3. Manually set your time zone (Time Zone). For Russia this is GMT+3 (Moscow) or GMT+5 (Ekaterinburg).
⚠️ Attention: B Juke 2017 with firmware 1.03.01 There is a bug - when manually setting the time via the radio, the dashboard shows 1 hour ahead. Solution: Update the firmware to 1.04.02 or set the clock only through the dashboard.

Until 2014 (analog instrumentation)

2014–2019 (digital tidy)

2020–2026 (with NissanConnect)

I don't know-->

4. Automatic synchronization: how to enable it and why it doesn’t work

In 理论上, automatic time adjustment should eliminate routine actions. In practice, owners Juke face three typical problems:

ProblemReasonSolution
Time gets lost after overnight stayWeak battery or oxidized terminalsClean the terminals, check the leakage current (normal: <50 mA)
Auto-sync doesn't workThere is no GPS signal or the SIM card is inactiveCheck roof antenna, update NissanConnect data
The clock “freezes” at one timeFactory firmware bug 1.03.01Update the software through your dealer or manually (instructions below)

To enable automatic synchronization:

  1. Go to Settings → Vehicle → Clock Settings.
  2. Activate Auto Time Update.
  3. Select source: GPS (default) or Mobile Network (requires SIM card).

If option Auto Time Update unavailable (gray), means:

  • 🚗 The machine is not connected to NissanConnect Services (check antenna and SIM card).
  • 📵 The GPS module is disabled in the settings (enabled in Settings → Location).
  • 🔌 ECU settings have been reset (you need to wait 10-15 minutes for initialization).
💡

If automatic synchronization is unstable, try manually specifying time zone instead of automatic detection. To do this in the menu Clock Settings turn off Auto Time Zone and select your region manually.

5. Resetting errors and glitches with the clock

If time is lost regularly, the reasons may be deeper than it seems. Here diagnostic sequence for Nissan Juke:

  1. Battery check:
    • Measure the voltage at the terminals with the ignition off (standard: 12.6–12.8V).
    • Start the engine - the voltage should rise to 13.8–14.4V.
    • If the values are lower, check the generator or replace the battery.
  • ECU diagnostics: 
    1. Выключите зажигание.

    2. Нажмите и удерживайте кнопку сброса пробега (TRIP).
    

    3. Включите зажигание (не запуская двигатель).
    

    4. Через 5 секунд на приборке появится сервисное меню.
    

    5. Кнопками ↑/↓ найдите пункт CLK ERR (Clock Error).
    

    6. Нажмите OK для сброса ошибки.

    • For models with NissanConnect There is hidden reset command:

    1. Go to Settings → System → About.
    2. Click 5 times in a row on Version Info.
    3. From the menu that appears, select Reset Time Sync.
    ⚠️ Attention: B Juke 2018 with firmware 1.03.01 after resetting the errors the clock may show 00:00 and disable manual adjustment. In this case disconnect the battery for 10 minutesto reset the ECU cache.
    What to do if the clock shows 23

    59 and do not change?:

    This is a known bug in the firmware 1.02.03 for Juke 2016. Solution:

    1. Disconnect the battery for 15 minutes.

    2. Plug it back in and immediately (within 30 seconds) set the time manually through the device.

    3. Do not turn on the ignition until the setup is complete!

    If the problem persists, the ECU will need to be reflashed by the dealer.

    6. Firmware update to correct time errors

    If all of the above methods did not help, the reason lies in ECU or multimedia system firmware. For Nissan Juke current software versions:

    Year of manufactureCurrent firmwareMinimum version for stable watches
    2010–20131.01.051.02.01 (corrects reset at -10°C)
    2014–20161.03.011.04.02 (fix GPS synchronization)
    2017–20192.01.032.02.01 (fixes freeze at 23:59)
    2020–20263.00.053.01.02 (optimized for ProPILOT)

    You can update the firmware in two ways:

    • 🔧 At the dealer (guaranteed, but paid - from 3,000 ₽).
    • 💻 On your own via USB (for advanced users only!).

    To update yourself:

    1. Download the firmware from the official website Nissan Owners (section Software Updates).
    2. Unzip the archive and copy the file update.ncn to a flash drive (FAT32, no more than 32 GB).
    3. Insert the flash drive into the USB port of the radio.
    4. Go to Settings → System → Software Update and follow the instructions.
    ⚠️ Attention: Do not remove the flash drive or turn off the ignition during the update! B Juke 2015 when the firmware is interrupted The radio goes into recovery mode, and a special cable will be required for recovery Nissan Consult III+ (the cost of the service at the dealer is up to 10,000 ₽).
    💡

    Updating the firmware solves 90% of problems with watches in Nissan Juke, but only if the reason is a software failure. If after the update the time is still lost, look for a problem in the hardware: battery, generator or GPS antenna.

    7. Frequently asked questions and myths about Juke clocks

    Let's look at popular misconceptions and real facts:

    • ❌ Myth: “The clock is lost because of the frost.”

      ✅ Reality: B Juke Before 2016, there was a bug with the temperature sensor, but this has been fixed in new versions. If the time goes wrong in winter, the problem is in the battery.

    • ❌ Myth: “Setting the time via phone (Bluetooth) breaks the clock.”

      ✅ Reality: Bluetooth synchronization only works on models with Android Auto and does not affect the tidy. But sometimes it conflicts with GPS synchronization.

    • ❌ Myth: “After replacing the dash lamps, the clock is reset.”

      ✅ Reality: This is only possible if the battery was disconnected during replacement or the ECU cable was damaged.

    If you bought Juke with mileage and the clock gets lost every day, first check:

    1. Date of last battery replacement (service life: 4–5 years).
    2. The presence of oxidation on the terminals and ground (especially under the tidy).
    3. Firmware version (via Settings → About).

    FAQ: Answers to popular questions

    Why does the clock in my 2015 Juke show the time an hour ahead?

    This is a known firmware bug 1.03.01, when, when manually tuning through the radio, the tidy adds +1 hour. Solution:

    1. Set the time in dashboard (button TRIP).
    2. Or update the firmware to 1.04.02.

    If updating is not possible, disable automatic synchronization in the radio (Settings → Clock → Auto Sync OFF).

    Is it possible to set the clock without inserting the key into the ignition?

    No. B Nissan Juke of all generations, access to time settings requires at least ignition on (position ACC or ON). This is a safety measure to prevent settings from being changed accidentally.

    The exception is models with NissanConnect and an active SIM card: they can synchronize over the network even when the ignition is turned off (but this consumes battery power).

    After replacing the battery, the clock is lost and cannot be adjusted. What to do?

    Most likely the ECU settings have been reset. Try:

    1. Wait 10–15 minutes with the ignition on (to initialize the system).
    2. If this does not help, reset the errors (instructions in section 5).
    3. As a last resort, disconnect the battery for 1 minute and repeat the setup.

    If the clock still does not adjust, check the fuse F27 (10A) in the block under the steering wheel - it is responsible for powering the device.

    How can I make the clock show seconds?

    B Nissan Juke until 2019 on the dashboard seconds not displayed This is a hardware limitation. However, in the multimedia system (if equipped), you can turn on the display of seconds:

    1. Go to Settings → Display → Clock Style.
    2. Select Digital with Seconds.

    In 2020+ models with TFT instrument panel seconds are shown by default in mode Sport Mode.

    Can I sync my Juke with Apple Watch or Android Wear?

    There is no direct synchronization, but there is a workaround:

    1. Connect your phone via Bluetooth to the radio.
    2. In your phone settings, enable Automatic time synchronization.
    3. B NissanConnect activate Phone Time Sync (Settings → Clock).

    Please note: this only works for displaying the time on the radio screen. Dashboard will not sync.