The trunk gas struts are a seemingly small detail, but the comfort of using the car depends on their serviceability. On Nissan Qashqai J11 (2013–2021) these elements often fail after 50–80 thousand kilometers: the trunk lid begins to fall, requires effort when opening, or closes with a loud bang. If you notice that the stops no longer lock the door in position, it's time to think about replacing it.

In this article we will look at everything you need to know about gas shock absorbers for Qashqai J11: how to determine the malfunction, which models are suitable (original and analogues), how to change them yourself without errors, and we will also give tips on extending their service life. We will pay special attention to the nuances that are not written about in standard instructions - for example, why new stops can “sag” after a month and how to avoid this.

Signs of malfunctioning gas stops on a Nissan Qashqai J11

The first signs of wear on gas shock absorbers often go unnoticed until the problem becomes critical. Pay attention to the following signals:

  • 🚗Trunk lid falls sharply When opened, it does not lock in the upper position.
  • 💨 To lift the door you need more effortthan before (especially in cold weather).
  • 🔊 Appears creaking or knocking when the stops are operating, this is a sign of gas leakage or rod wear.
  • 🔄 Door closes on its own when trying to leave it open (even at a small angle).
  • 🌡️ In hot or cold weather, the stops work unstable - this indicates a loss of tightness.

If at least one of these signs appears, check the condition of the shock absorbers. You should not delay replacement: faulty stops can lead to damage to trunk hinges or even injury (for example, if a door suddenly falls on your hand).

⚠️ Attention: On Qashqai J11 with an electric trunk (optional), faulty gas struts can cause error in the system and door lock. In this case, diagnostics of the control unit is required.
📊 How often do you check the gas stops on your car?
  • Only when they break
  • Once a year
  • At every maintenance
  • Never checked

Which gas struts are suitable for Nissan Qashqai J11: original vs analogues

On Nissan Qashqai J11 (including restyling 2017) gas struts are installed with the following characteristics:

  • 🔧 Compressed length: ~380 mm
  • 📏 Unfolded length: ~630 mm
  • 💪 Force (compression force): 500–600 N (newtons)
  • 🔗 Mounting type: ball pin with M8 thread (both ends)

Original stops from Nissan have an article number 80710-4M00A (left) and 80710-4M00B (right). Their average price is 2,500–3,500 rubles. per piece. However, many owners choose analogues from trusted brands that are not inferior in quality, but are cheaper.

Brand Article Price (for 1 piece), rub. Features
Sachs 100 537 1 800–2 200 High quality seals, resistance to temperature changes
Stabilus 0827NJ 2 000–2 400 Original supplier for many automakers, service life up to 100 thousand km
Monroe G1028 1 500–1 900 Budget option, but less durable in temperatures below -20°C
Febi Bilstein 22610 1 700–2 100 Good price/quality ratio, suitable for regions with temperate climates

Important: on the Qashqai J11 since 2017 (restyling), stops with a different force (600–650 N) were sometimes installed. Before purchasing, check the markings on old shock absorbers or check the vehicle's VIN.

💡

If you buy non-original brand stops, pay attention to the country of production. For example, Stabilus from Germany or Poland lasts longer than counterparts from China, even with the same article number.

Step-by-step instructions for replacing gas struts on a Nissan Qashqai J11

Replacing trunk shock absorbers is a procedure that even a beginner can handle. You will need:

  • 🔧 Set of sockets or open-end wrenches (size 10 mm And 13 mm).
  • 🔨 Flat screwdriver (for prying off the fasteners).
  • 🧤 Gloves (so as not to get your hands dirty or get hurt on sharp edges).
  • 🛢️ WD-40 or similar lubricant (if the fasteners are rusty).

Procedure:

  1. Preparation. Open the trunk and secure it in the up position (for example, by resting it on a rack or asking an assistant to hold it).
  2. Removing the old stop.
    • Unscrew the nut securing the stop to the body (the key is on 13 mm).
    • Remove the ball pin from the trunk hinge by prying it off with a screwdriver.
    • Carefully remove the shock absorber. Be careful - there may be gas under pressure in it!
  3. Installing a new stop.
    • Secure the new shock absorber to the trunk hinge by snapping the ball pin into place.
    • Screw the other end to the body and tighten the nut.
  • Check. Close and open the trunk several times to make sure the lock operates smoothly.

    • Is there any misalignment of the trunk door|The stops hold the lid in any position|The fastening nuts are tightened securely|There are no gas leaks (check by touch to see if the rod is oily)-->

    ⚠️ Attention: If the stops are tight after replacement, do not try to “work” them out by force. Most likely, you installed models with excessive force (for example, 700 N instead of 500 N). This will lead to rapid wear of the hinges!

    Typical replacement mistakes and how to avoid them

    Even a simple operation to replace gas stops can result in problems if you do not take into account several nuances:

    • 🔄 The left and right stops are mixed up. On Qashqai J11 they are symmetrical in fastenings, but may differ in force. Always check the labeling!
    • 🔧 Insufficient tightening of nuts. If the fastening becomes loose, the stop may be pulled out when the trunk is opened suddenly.
    • 🧊 Replacement in cold weather. At temperatures below -10°C, the gas in the shock absorbers is compressed and the new stops may feel "hard". Let them warm up in a warm room before installing.
    • 🛠️ Using WD-40 on rubber seals. The lubricant corrodes the rubber, which leads to gas leakage. To clean fasteners, use only white spirit.

    Another common mistake is buying stops “by eye”, without checking the characteristics. For example, shock absorbers from Nissan X-Trail T32 similar in appearance, but have a different force (700 N), which will lead to premature wear of hinges on Qashqai J11.

    What to do if the new stop “sank” after a month?

    If the shock absorber loses force shortly after installation, the reasons may be as follows:

    1. **Factory assembly defect** - check the warranty with the seller.

    2. **Improper storage** - stops cannot be stored in a horizontal position for more than 2 months (gas flows to one side).

    3. **Excessive load** - for example, if you often hang heavy bags on an open trunk.

    In any case, contact the seller for a replacement under warranty (usually 1-2 years).

    How to extend the life of gas struts

    The average life of gas shock absorbers is Nissan Qashqai J11 — 5–7 years or 80–100 thousand km. But with proper use, this period can be increased:

    • 🧴 Lubricate the rods. Apply a thin layer once a year silicone grease (not lithol!) on the visible part of the rod. This will protect against corrosion and reduce friction.
    • ☀️ Avoid direct sunlight. Park in the shade or use a trunk cover - ultraviolet radiation destroys rubber seals.
    • ❄️ Do not jerk open the trunk in cold weather. At temperatures below -15°C, the gas in the shock absorbers becomes less mobile and sudden force can damage the seals.
    • 🚿 Wash the fastenings. Dirt and salt from the roads get onto the ball pins, causing corrosion. Clean them with water and car shampoo every six months.

    If you frequently transport heavy loads, consider installing high force stops (600–650 N). However, remember that this will increase the load on the hinges, and they will also have to be replaced more often.

    💡

    Regular maintenance of gas shock absorbers not only saves money on replacement, but also prevents expensive repairs of trunk hinges, which can cost 10–15 thousand rubles.

    Where to buy gas struts for Nissan Qashqai J11: verified sellers

    When purchasing shock absorbers, it is important to avoid counterfeits, especially if you choose brands Sachs or Stabilus. We recommend the following trusted sources:

    • 🛒 Official Nissan dealers. The guarantee of original parts is 2 years, but the price is higher than that of analogues.
    • 🌍 Online stores:
      • Exist.ru — wide range, there are customer reviews.
      • Autodoc.ru — convenient selection by VIN code, frequent discounts.
      • Emex.ru — original spare parts with a guarantee.
    • 🏬 Local spare parts stores. Before purchasing, check whether the stops have brand hologram and whether the article matches the catalogue.

    When purchasing online, be sure to check:

    • 📦 Warranty period (minimum 1 year).
    • 📄 Availability of a certificate of conformity (for branded analogues).
    • 🚚 Return Policy, if the part does not fit.
    ⚠️ Attention: Counterfeits of brands are often sold in markets and uncertified stores. Stabilus or Sachs. You can distinguish them by the quality of the paint (there are no drips on the original), markings (embossed clearly, without errors) and packaging (there must be a branded blister).

    Frequently asked questions (FAQ)

    Is it possible to replace only one gas stop if the second one is still working?

    Not recommended. Even if the second stop looks good, it is already worn out and may fail in the near future. In addition, different forces on the left and right sides will lead to trunk lid distortion and accelerated wear of hinges.

    How long does it take to replace stops on a Qashqai J11?

    If you have tools and an assistant (to hold the trunk lid), the procedure will take 20–30 minutes. If the fasteners are rusty, it may take up to an hour (including WD-40 and waiting).

    What is the difference between the stops for Qashqai J10 and J11?

    On Qashqai J10 (2006–2013) shock absorbers were installed with a different fastening (M10 thread instead of M8) and a force of 450–500 N. Stops from J10 don't fit for J11, despite the external similarity. Also on J11 after restyling in 2017, sometimes there are stops with a force of 600 N (article 80710-4M01A).

    Can the gas strut be repaired or is it just a replacement?

    Theoretically, there are shops that recharge gas shock absorbers, but for car shock absorbers this is inappropriate. The cost of repair is comparable to the price of a new stop, but there is no warranty on the work. In addition, after recharging, the stop may lose its seal after a few months.

    Why do new stops creak when working?

    The squeak is usually caused by:

    1. Lack of lubricant on the rod - apply silicone grease.
    2. Misalignment during installation - check whether both ends of the stop are secured evenly.
    3. Low quality rubber seals (typical of cheap analogues).

    If the squeak does not go away after lubrication, return the stops under warranty.