Nissan Note E11 (2006–2013) - a compact hatchback that is still in demand due to its reliability and practicality. However, even such cars have weak points, and one of them is the headlight washer system. Over time, the nozzles responsible for supplying fluid to the optics become clogged, break, or begin to work incorrectly. If you notice that the stream is weak, the liquid flows past or does not flow at all, the problem lies with them.
In this article we will look at everything you need to know about headlight washer nozzles for Nissan Note E11: from signs of malfunction to step-by-step instructions for replacement. We have also prepared a table with original articles and analogues, cleaning tips and answers to frequently asked questions. The material will be useful for both beginners and experienced car owners who want to save money on service stations.
Signs of malfunctioning headlight washer nozzles
The first signal that something is wrong with the injectors is a deterioration in the quality of headlight cleaning. But there are other symptoms that cannot be ignored:
- 🔦 Weak fluid pressure or its complete absence when the washer is turned on. Most often this indicates a clogged nozzle or tube.
- 💦 Liquid splashes to the sidewithout hitting the headlight. The reason is mechanical damage to the injector or wear of the o-ring.
- ⚡ The washer operates jerkily or delayed. This may be due to an electrical problem (for example, oxidation of contacts).
- 🚨 The fault light is constantly on on the dashboard (if your Note E11 equipped with this function).
If you notice at least one of these signs, do not delay diagnosis. Clogged nozzles not only impair visibility at night, but can also cause the lamps to overheat due to detergent residue on the glass.
⚠️ Attention! On Nissan Note E11 With xenon headlights, faulty washer nozzles can cause a refusal to pass technical inspection. According to traffic regulations, xenon lamps must be equipped with a working cleaning system.
- Once a month
- Only before inspection
- When I notice a problem
- Never checked
Original articles and analogues of injectors for Nissan Note E11
Before purchasing a new injector, make sure you choose a part that is compatible with your modification. On Note E11 Two types of injectors were installed depending on the year of manufacture and configuration:
| Nozzle type | Original article | Manufacturer | Analogs (brand + article) | Note |
|---|---|---|---|---|
| Standard (2006–2010) | 28550-4M000 |
Nissan | Febi 28550, Meyle 3142855000 | Suitable for most versions with halogen headlights |
| Strengthened (2010–2013) | 28550-4M001 |
Nissan | Hella 8ZL355369321, Valeo 698558 | Used in configurations with xenon |
| Universal (for left/right side) | 28550-JM00A |
Nissan | JP Group 1196500100, Topran 1010285 | Suitable for replacement on both sides |
When choosing an analogue, pay attention to body material. Original injectors Nissan are made of plastic with ultraviolet protection, while cheap analogues can crack due to temperature changes. Also check the package contents: some sets do not contain o-rings, which will have to be purchased separately (item no. 01516-4M000).
Important: The nozzles for the left and right headlights are on Note E11 not interchangeable! They have different spray geometries, so buy in pairs or check the side with the seller.
How to clean headlight washer nozzles without removing them
If the problem is only clogged, you can try to restore functionality without dismantling. This method is suitable for light pollution and requires a minimum set of tools:
Needle syringe (5-10 ml)|Distilled water or special liquid for cleaning injectors|Compressor or pump with a fine nozzle|Lint-free wipes|Safety gloves-->
Step by step instructions:
Remove the washer reservoir cap and pump out the liquid (you can use the same syringe). Fill the tank clean water or injector cleaning solution (for example, LIQUI MOLY JetClean).
Activate the headlight washer several times to allow fluid to flow through the system. If the pressure is weak, proceed to the next step.
Disconnect the supply hose from the nozzle (it is secured with a plastic clip - carefully press it out with a screwdriver). Place a syringe containing cleaning solution onto the hose and press the plunger firmly to create pressure. Repeat 3-4 times.
Reconnect the hose and check operation. If the stream is still weak, blow out the nozzle with a compressor from the reverse side (from the side of the attachment to the body).
If the problem remains after cleaning, you will have to remove the nozzle for deep rinsing or replacement. Most often clogged strainer inside the case - it can be carefully removed and washed in an ultrasonic bath (if available).
⚠️ Attention! Do not use metal objects (needles, wire) for cleaning - they can damage the nozzle and aggravate the problem. Also avoid harsh solvents (such as acetone) that will attack plastic.
If you don’t have a special liquid on hand, you can use a mixture of distilled water and vinegar (3:1 ratio). It dissolves lime deposits well, but is not suitable for regular use.
Step-by-step replacement of headlight washer nozzles Nissan Note E11
If cleaning does not help, you will have to install a new part. The process is not complicated, but it requires care - especially when working with plastic clips and hoses. Average time to replace one injector: 20–30 minutes.
Tools:
- 🔧 Flat head screwdriver (small)
- 🔨 Plastic puller or awl
- 🛠️ 10 mm wrench (for some modifications)
- 🧴 Silicone grease (for O-rings)
Instructions:
Open the hood and find the injector. On Note E11 it is located on the bumper, next to the headlight. First remove plastic cover (if there is one) - it is secured with latches.
Disconnect electrical connector (press the lock and pull to the side). If the contacts are oxidized, clean them with alcohol.
Squeeze the plastic clamp of the fluid supply hose and remove it. Be careful - the hose may be brittle due to aging rubber.
Unscrew the nozzle counterclockwise (it is held on by a threaded connection). If it does not budge, use a 10 mm wrench, but do not use excessive force.
Install the new injector in reverse order. Don't forget to lubricate the O-ring silicone grease to avoid leaks.
Check the operation of the system by filling the reservoir with washer fluid. The jet should hit exactly the center of the headlight.
If after replacement the fluid continues to flow past, check nozzle installation angle. On Note E11 it should be directed slightly upward (about 10–15°). If necessary, adjust the position by placing a thin shim under the base.
What to do if the nozzle does not unscrew?
If the thread is “stuck”, do not try to tear it off by force - this will break the fastener. First treat the joint with a penetrating lubricant (eg WD-40) and wait 10–15 minutes. Then gently rock the nozzle from side to side while turning it. As a last resort, you can drill out the housing and replace the entire assembly.
Typical replacement mistakes and how to avoid them
Even experienced car owners sometimes make mistakes that lead to repeated breakdowns or leaks. Here are the most common of them:
- 🔧 Using sealant instead of an O-ring. The sealant cracks over time and leads to liquid leaks onto the optics. Always use original rubber seals.
- ⚡ Incorrect electrical connection. If the polarity is reversed, the nozzle will not work, and in some cases the washer control unit may burn out.
- 💧 They forget to bleed the system after replacement. Air remains in the hoses, which is why the washer operates jerkily during the first few presses.
- 🔨 Use of excessive force when unscrewing. This leads to thread breakage or breakage of the plastic bumper housing.
Another common problem is incompatibility of the new injector with the system. For example, if you install a part from Nissan Micra Instead of the original one, the pressure may be too weak or, conversely, too strong. Always check the compatibility chart (see section above).
⚠️ Attention! On some versions Note E11 with xenon injectors have a built-in heating. If you install a regular nozzle without this feature, the liquid will freeze in the nozzle in winter. Check the presence of heating by markings: there are letters on the heating nozzles HT in the article.
Before purchasing a new injector, be sure to remove the old one and compare them visually. Even if the part numbers are the same, there may be differences in nozzle length or thread diameter.
How to extend the life of headlight washer nozzles
To avoid frequent breakdowns, just follow a few simple rules:
- 🌡️ Use quality washer fluid. Cheap compounds with a high alcohol content corrode rubber seals and leave residue on the nozzles. The best option is liquids based on isopropyl alcohol (for example, Sonax Xtreme or Liqui Moly Scheiben-Frostschutz).
- 🚿 Flush the system before winter. Before the first frost, fill the reservoir with clean water and turn on the washer to wash out any remaining summer fluid. Then fill the tank with winter compound.
- 🔍 Check the fluid level regularly. Dry operation leads to overheating of the pump and clogging of the nozzles with dirt particles from the bottom of the tank.
- 🛠️ Clean the nozzles every six months. It is enough to walk over them with a soft brush (for example, a toothbrush) and blow with a compressor.
If you often drive on dusty roads, install additional filter to the fluid supply hose. It can be made from a piece of foam rubber or a purchased special filter for washer fluids (item no. 28550-FILTER from Nissan).
Also note system pressure. If the pressure is weak even after cleaning the injectors, the problem may be washer pump (article 28500-4M000). Its resource is about 100,000 km, after which performance drops by 30–40%.
Frequently asked questions about headlight washer nozzles Nissan Note E11
Is it possible to drive without a working headlight washer?
Technically yes, but it's not safe. Dirt on the headlight glass reduces light transmission by up to 40%, which impairs visibility at night. In addition, the absence of a washer on xenon headlights is a violation of traffic regulations (fine up to 500 rubles).
Why does fluid flow under the bumper after replacing the injector?
Most likely, you installed the O-ring incorrectly or forgot to lubricate it. Remove the nozzle and check the integrity of the rubber gasket. The cause may also be a crack in the body of the new part (defect).
How to adjust the direction of the jet?
On Note E11 The nozzles are adjusted by turning the housing. Loosen the fastening, direct the stream to the center of the headlight and fix the position. If adjustment does not help, check the integrity of the nozzle - it could be deformed.
Can injectors from other Nissan models be used?
Partially. For example, injectors from Nissan Micra K13 (article 28550-JM000) are suitable for mounting, but have a different spray angle. From Nissan Juke (article 28550-4M025) - only for versions with xenon.
What should I do if the washer works, but no fluid flows?
Check:
1) Hoses for kinks or cracks.
2) Filter in the tank (it could be clogged).
3) Pump - When turned on, a slight hum should be heard. If not, check the fuse F37 (10A) in the block under the steering wheel.