Original wheels for Nissan Juke R17: sizes, parameters and selection recommendations

Crossover Nissan Juke first generation (body code F15/R17, 2010–2019) has become a cult classic due to its eccentric design and dynamic performance. However, when choosing wheels, owners often encounter confusion: which sizes are considered original and which are acceptable for tuning? In this article we will analyze exact factory parameters rims for Juke R17, including diameter, offset (ET), bolt pattern (PCD) and bore diameter (DIA).

It is important to understand that even minor deviations from the recommended dimensions can lead to problems: from premature suspension wear to system errors ESP And ABS. We analyzed data from official catalogs Nissan, service manuals and owner experience to provide up-to-date information. If you are planning on replacing drives, bookmark this article to avoid costly mistakes.

Official wheel sizes for Nissan Juke R17 (2010–2019)

Factory disk settings for Nissan Juke first generation depend on the configuration and year of manufacture. Basic versions (eg Visia or Acenta) equipped with steel wheels 16 inches, while the top ones (Tekna, Nismo) received light alloy 17–18 inches. Below is a list of original sizes indicating acceptable variations:

• 🔧 Diameter: 16", 17" (standard), 18" (optional for Nismo and packages Sport).
• 📏 Rim width: 6.0J–7.0J (depending on diameter).
• ⚖️ Departure (ET): +38 mm for 16", +40 mm for 17", +35 mm for 18".
• 🔄 Bolt Pattern (PCD): 5×114.3 mm (unified for all versions).
• 🕳️ Bore diameter (DIA): 66.1 mm.

Please note: parameters for the restyled version (Juke 2014–2019) remained unchanged, with the exception of special editions (for example, Juke Nismo RSwhere the disks were used 18×7.5J ET35). If your car is equipped with a system 4WD, installation of disks with a width of up to 7.5J, but with mandatory offset adjustment.

Table of original disk parameters by configuration

To simplify the choice, we have compiled the data into a table taking into account the factory configurations. If your version Juke is not specified - rely on the closest analogue by year of manufacture and drive type.

Equipment	Year of manufacture	Diameter/Width	Departure (ET)	PCD/DIA	Disk type
Visia (basic)	2010–2014	16×6.0J	+38 mm	5×114.3 / 66.1	Steel
Acenta, N-Connecta	2011–2019	17×6.5J	+40 mm	5×114.3 / 66.1	Cast (aluminium)
Tekna, Sport	2012–2019	17×7.0J	+40 mm	5×114.3 / 66.1	Cast (optional two-color)
Nismo, Nismo RS	2013–2019	18×7.5J	+35 mm	5×114.3 / 66.1	Cast (special design)
4WD (all-wheel drive)	2010–2019	17×7.0J	+38–40 mm	5×114.3 / 66.1	Cast/steel

Critical nuance: discs with an offset of less than +35 mm may touch suspension elements or brake calipers, especially on versions with larger brake discs (for example, Nismo RS). Before purchasing, be sure to check compatibility with your modification through the service Nissan EPC or from an authorized dealer.

Acceptable non-original sizes: what can be installed without risks?

Many owners Juke R17 tend to install larger diameter wheels to improve appearance. However, not all options are safe. Below is a list valid alternatives, confirmed by the experience of the tuning studio and road tests:

• 🚗 17 inches: width 6.5J–7.5J, offset +35–45 mm. The optimal choice for a balance of appearance and comfort.
• 🏎️ 18 inches: width 7.0J–8.0J, offset +30–38 mm. Requires low profile rubber (e.g. 215/45 R18).
• ⚠️ 19 inches: installation is only possible with an offset of +25–30 mm and a width of up to 8.5J, but this will lead to deterioration in handling and the risk of damage to the suspension.

When choosing non-original disks, consider:

1. Tire compatibility: e.g. for rim 17×7.0J ET40 suitable tires 215/55 R17 or 225/50 R17.
2. Ground clearance: wheels with a diameter >18" reduce ground clearance by 5–10 mm.
3. Load on the wheel bearing: increasing the width of the disk by more than 1.5" from the original reduces its life.

How to check rim compatibility for Nissan Juke R17?

Even if the disk parameters match the original ones, this does not guarantee 100% compatibility. Here is a step-by-step verification algorithm:

1. Step 1: Make sure the bolt pattern (PCD 5×114.3) and bore diameter (DIA 66.1) are identical to factory ones. Use WillTheyFit service for virtual fitting.
2. Step 2: Check departure (ET). Permissible deviation: ±5 mm from the original. For example, for 17" wheels the offset can be +35–45 mm.
3. Step 3: Measure the gap between the disc and the brake caliper. The minimum distance is 15 mm.
4. Step 4: Install the disc on the hub and spin the wheel on a jack to make sure there is no friction on the suspension.

Make sure PCD (5×114.3) and DIA (66.1) match|Check offset (ET) with a tolerance of ±5 mm|Measure the gap to the caliper (minimum 15 mm)|Check that there is no friction when rotating the wheel|Check the rim width with the recommended one for your tires-->

If you buy used wheels, pay attention to:

• 🔍 Chips and cracks on the inside (especially critical for alloy wheels).
• 🔧 Deformation: Place the disc on a flat surface and check the runout.
• 🛠️ Traces of repair: Welds or primer may indicate accident repair.

What happens if you install a disk with the wrong DIA?

If the wheel mounting diameter (DIA) does not match the hub diameter (66.1 mm for Juke R17), the wheel will be installed misaligned. This will lead to:

- vibrations at speeds above 80 km/h;

- uneven wear of the wheel bearing;

- risk of the wheel coming off during emergency braking.

As a last resort you can use centering rings, but this is a temporary solution.

Top 5 mistakes when choosing wheels for Nissan Juke R17

Analysis of owner forums Juke showed that most disk problems arise from common errors. That's what can't do when selecting:

1. Ignore departure (ET). Discs with ET < +30 mm or > +45 mm change the load on the suspension and can lead to damage to the shock absorbers.
2. Install disks with PCD 5x112. Despite the visual similarity, the bolt pattern 5×112 (for example, from VW) is incompatible with 5×114.3 and will lead to wheel runout.
3. Choose rim width >8.0J without modification of arches. This will cause the tire to rub against the fender liners when turning.
4. Save on centering rings. Cheap plastic rings are deformed and do not provide reliable fixation.
5. Ignore seasonality. For example, for winter tires on 17" wheels, the recommended rim width is 6.5J–7.0J, not 7.5J.

⚠️ Attention: On versions Juke Nismo RS with brake discs 320 mm Standard 17" wheels may not fit due to the larger caliper. In this case, high clearance discs are required (for example, Rays Gram Lights 57DR).

Recommended brands and wheel models for Juke R17

If you are looking for quality wheels for Nissan Juke, pay attention to proven brands and models that owners often install:

Brand	Model	Options	Type	Notes
Enkei	PF05	17×7.0J ET40, 5×114.3	Cast	Light weight, suitable for Tekna
BBS	CH-R	18×7.5J ET35, 5×114.3	Forged	High strength, compatible with Nismo
OZ Racing	Ultraleggera	17×7.0J ET38, 5×114.3	Cast	Classic design, suitable for restyling
Nissan Original	Article 40500-4M000	17×6.5J ET40, 5×114.3	Cast	Original for Acenta/N-Connecta

When choosing a brand, focus on:

• 🏆 Reputation: Enkei, BBS, OZ And Rays guarantee balance and strength.
• 💰 Price/quality ratio: disks Replica (copies of originals) are cheaper, but may have an imbalance.
• 🔧 Guarantee: official dealers Nissan provide a 2-year warranty on original discs.

FAQ: Frequently asked questions about wheels on Nissan Juke R17

Is it possible to install 18" wheels on the basic version of Juke Visia 2011?

Technically yes, but you will need:

• Select wheels with offset ET35–38 and width 7.0J–7.5J.
• Install low profile tires (for example, 215/45 R18).
• Check the clearance with the caliper - on Visia brake discs are thinner than on Nismo.

However, this may affect comfort (suspension stiffness will increase) and the life of the wheel bearings.

What are the differences between 2WD and 4WD Juke wheels?

The main difference is permissible overhang:

• For 2WD (front wheel drive) fits wheels with ET38–45.
• For 4WD (all-wheel drive) recommended ET35–40 due to the wider rear wheels.

Also on 4WD versions often install wider rims (up to 7.5J), since the rear axle experiences a large load.

What wheels are suitable for winter tires on the Juke R17?

Optimal for winter tires:

• 🔹 Diameter: 16" or 17" (18" not recommended due to high profile rubber).
• 🔹 Rim width: 6.0J–7.0J (for tires 205/60 R16 or 215/55 R17).
• 🔹 Departure: ET38–42 (closer to the original to maintain controllability).

Using narrow disks (for example, 6.0J) improves self-cleaning of snow from tires.

What is the maximum wheel diameter that can be installed on a Juke without modifications?

18 inches - this is the limit for most versions Juke R17 no modification to arches or suspension. However:

• On Nismo RS installation possible 19", but with departure ET25 and rubber 225/40 R19.
• For versions with springs Sport (reduced) maximum diameter - 17", otherwise the wheel will touch the arch.

Before installation necessarily Check the gap using a ruler or template.

Where to buy original wheels for Juke R17?

Original wheels Nissan you can order:

• 🔧 U official dealers (articles: 40500-4M000 for 17", 40500-4M100 for 18").
• 🌍 On sites Nissan Parts Europe or Amayama (shipping from Japan).
• 🛒 In spare parts stores (for example, Exist.ru, Autodoc), but check the certificates.

Cost of original discs: from 12,000 rubles. for 17" and from 18,000 rubles for 18".