Selection of rims for Nissan Tiida - a task that requires attention to detail. One key parameter that is often overlooked is hub center bore diameter (DIA). An error in this parameter can lead to vibrations at speed, accelerated bearing wear, and even damage to the disk. In this article we will look at what exactly the diameter of the hub is Tiida different generations, how to measure it correctly and what to do if the disk does not fit the DIA.
Models Nissan Tiida (body J31 And J32) have standard wheel mounting parameters, but even here there are nuances. For example, restyled versions may differ in tolerances, and sports modifications (for example, Tiida Sport) sometimes require non-standard solutions. We have collected current data confirmed by the manufacturer and experienced car owners so that you can avoid common mistakes.
Standard hub diameter Nissan Tiida: official data
For most versions Nissan Tiida (2004–2019) hub center bore diameter (DIA) is 66.1 mm. This setting is the same for:
- 🚗 Tiida Sedan (body
J31, 2004–2012) - 🚗 Tiida Hatchback (body
C11, 2004–2012) - 🚗 Tiida Latio (for the Asian market, body
J32, 2007–2019) - 🚗 Tiida Sport (sports versions with 1.8-liter engine)
Important: Some discs after 2012 (especially for Southeast Asian markets) may have DIA 67.1 mm - this is due to the unification of the platform Nissan B and compatibility with models Note And March. Always check the parameters for your specific VIN.
- J31 (Sedan)
- C11 (Hatchback)
- J32 (Latio)
- I don't know
How to measure the hub diameter yourself: step-by-step instructions
If you are not sure about the parameters of your car or are buying used wheels, it is better to measure the DIA yourself. For this you will need caliper or an exact ruler. Follow the algorithm:
- Remove the wheel and clean the hub from dirt.
- Find the center hole - it is located in the center of the hub where the wheel is attached.
- Measure the hole diameter in millimeters. For accuracy, take measurements in two perpendicular planes.
- Compare the result with the compatibility table (see below).
Removed wheel|Calipers or ruler|Clean rags|Flashlight (to illuminate the hub)-->
⚠️ Attention: Do not confuse hub diameter with PCD (bolt pattern)! PCD for Tiida - this is 4×114.3 (4 holes on a circumference of 114.3 mm), and DIA is a separate parameter. An error in the PCD will lead to the inability to secure the disk, and an incorrect DIA will lead to runout and play.
Disc compatibility table for Nissan Tiida by year
| Model and year | DIA (mm) | PCD | Departure (ET) | Recommended rim width |
|---|---|---|---|---|
| Tiida J31 (2004–2007) | 66.1 | 4×114.3 | 35–45 | 6.0J–7.0J |
| Tiida J31 (2008–2012, restyling) | 66.1 | 4×114.3 | 38–48 | 6.5J–7.5J |
| Tiida Latio J32 (2007–2019, Asia) | 66.1 or 67.1* | 4×114.3 | 35–50 | 6.0J–8.0J |
| Tiida Sport (1.8L, 2006–2012) | 66.1 | 4×114.3 | 38–42 | 7.0J–8.0J |
*For Tiida Latio J32 after 2015, DIA 67.1 mm is possible - check by VIN or hub catalog number.
If your rim has a DIA of 67.1mm and your hub is 66.1mm, you can use centering rings (adapters) 0.5 mm thick. But this is a temporary solution - it is better to select a disk with an exact match.
What happens if you choose the wrong hub diameter?
Non-compliance with DIA leads to serious problems:
- 🔄 Vibration at speed (especially noticeable at 80–120 km/h) due to imbalance.
- 🔧 Accelerated wear wheel bearing and ball joint.
- 💥 Risk of wheel separation during a sharp maneuver (if the disk does not “sit” tightly on the hub).
- 🔩 Balancing problems - even after the procedure, the beating may remain.
⚠️ Attention: If the disk has DIA morethan the hub (eg 67.1mm instead of 66.1mm), it can be installed using centering rings. But if DIA less — the disc will not physically fit onto the hub!
Is it possible to drive with a mismatched DIA?
Yes, but only for a short time (for example, to get to a service station). Long-term use will lead to:
- deformation of holes in the disk,
- wheel play,
- damage to the threads of the fastening bolts.
The recommended maximum is 500 km at a speed no higher than 80 km/h.
How to select wheels with non-standard DIA: centering rings and adapters
If you have found the ideal rim design, but their DIA does not match the hub Tiida, there is a way out - centering rings. They are made of aluminum or plastic and compensate for the difference between diameters. Selection rules:
- 📏 Ring thickness = (Disc DIA - Hub DIA) / 2. For example, for a 67.1 mm disc and a 66.1 mm hub you need a ring thickness
0.5 mm. - 🔍 Material: aluminum is preferable to plastic (less wear).
- 🔧 Installation: the ring should fit snugly on the hub no play.
⚠️ Attention: Centering rings are temporary solution. As soon as possible, replace the drives with ones that comply with DIA. The rings can become wrinkled under heavy loads (for example, when falling into a hole), which will lead to beating.
Before purchasing rings, check their compatibility with the mounting bolts. Some rings have cutouts for bolt heads to make installation easier.
Common mistakes when choosing disks for Nissan Tiida
Even experienced car owners sometimes make mistakes. Here are the most common mistakes:
- Ignore departure (ET). A disc with the wrong offset may touch the arch or suspension. For Tiida optimal ET -
38–45 mm. - Purchasing discs using “universal” parameters. For example, disks from Nissan Note may not be suitable due to different DIA (for Note often 67.1 mm).
- Disk width not taken into account. Disks that are too wide (more than 8J) require rolling out the arches or using spacers, which is unsafe.
- Savings on centering rings. Cheap plastic rings wear out quickly and can slip.
To avoid mistakes, always check the parameters with manufacturer's catalog or use online selection services (for example, DiskCalc.ru or Wheelfit.me).
FAQ: Answers to popular questions about the hub Nissan Tiida
Is it possible to install discs from Nissan Almera N16 on Tiida?
No, despite the similar PCD (4×114.3), y Almera N16 hub diameter 60.1 mm, which is significantly less. Thick centering rings required 3 mm, but this is not safe - it is better to choose disks specifically for Tiida.
What is the maximum reach (ET) allowed for Tiida?
For most versions the maximum reach is ET48. Exceeding this value will result in the brake caliper hitting the brake caliper. Minimum reach - ET35 (for wide rims).
What should I do if vibration appears after installing new disks?
The reasons may be different:
- DIA mismatch (even by 0.5 mm).
- Poor balancing.
- Deformed disc (check on a bench).
- Wheel bearing wear.
Start by checking the alignment of the disc on the hub and re-balancing.
Where to find original disks for Tiida?
Original wheels Nissan can be ordered by catalog numbers:
40500-JM00A— steel disk 15" (ET45).40500-4M000— 16" alloy wheel (ET42).40500-4M010— 17" light alloy wheel (ET40, for Tiida Sport).
Also suitable are discs from Renault Megane II (with the same PCD and DIA).
Is it possible to increase the diameter of the hub by boring?
Technically possible, but highly not recommended. Boring weakens the hub, which can lead to its destruction under load. If you need a larger DIA (for example, 67.1 mm), it is better to replace the hub with an analogue from Tiida Latio J32.