Mud flaps for Nissan Qashqai J10: complete selection and installation guide

Mudguards are not just a decorative element Nissan Qashqai J10, but a critical part that protects the body from corrosion, chips and premature wear. Owners of the first generation crossover (2007–2013) often face the problem of selecting high-quality spare parts, because the original mudguards are from Nissan are expensive, and analogues vary in price and materials. In this article we will look at how to choose mud flaps for J10 taking into account the features of the model, which materials are preferable, and how to avoid common mistakes during installation.

Feature Qashqai J10 - in its design: the front and rear mudguards have different geometries, and the fastenings may differ depending on the configuration (for example, for versions with 4WD or 2WD). We analyzed reviews from car owners, tests from independent experts and manufacturer data to create the most practical guide possible. Here you will find not only the theory, but also step-by-step instructions with photos, comparative tables of materials and answers to frequently asked questions.

Why do mud flaps on the Qashqai J10 fail faster than on other models?

Construction Nissan Qashqai J10 has several “weak points” that accelerate the wear of mudguards:

• 🔧 Low ground clearance (185 mm) compared to competitors (Toyota RAV4 — 197 mm, Honda CR-V - 208 mm), due to which the mudguards come into contact with the road surface more often.
• 🌧️ Poor ventilation of arches: factory mudguards J10 do not have sufficient drainage holes, which leads to the accumulation of dirt and moisture.
• 🛠️ Material of original parts: Many owners note that standard mudguards are made of too soft plastic, which cracks at subzero temperatures.

In addition, in models before the 2010 restyling, the mudguard mounts are made of metal that is prone to corrosion. This leads to the fact that even with a slight impact, the latches break and the mudguard begins to dangle. In later versions (2011–2013), the problem was partially solved through the use of plastic clips, but they also do not last forever.

⚠️ Attention! If you notice that the mudguard is on Qashqai J10 began to move away from the arch, do not delay repairs. Driving for a long time with damaged protection leads to sand and salt getting on the paintwork, which causes corrosion of sills and rear wings after 1–2 winters.

Types of mud flaps for Nissan Qashqai J10: comparison of materials and manufacturers

There are mud flaps on the market for J10 of four main materials, each of which has pros and cons. Below is a comparison table taking into account prices and durability:

Material	Service life	Average price (set)	Pros	Cons
Original plastic (Nissan)	3–5 years	8 000–12 000 ₽	Perfect fit, UV resistant	High price, fragile in frost
Polyurethane (eg. Hepu)	5–7 years	5 000–7 000 ₽	Impact resistance, flexibility	May deform at high temperatures
Rubber (budget analogues)	1–2 years	2 000–3 500 ₽	Low price, easy installation	Cracks quickly and loses elasticity
Aluminum (tuning options)	10+ years	15 000–25 000 ₽	Maximum protection, stylish look	Difficult to install, risk of fastening corrosion

For most owners Qashqai J10 The optimal choice would be polyurethane mud flaps from trusted brands such as Hepu, Febi or Mannol. They combine reasonable price and durability, and their installation does not require modifications. Original parts from Nissan It's worth buying only if you plan to use the car for a long time without tuning.

How to choose the right mudguards: part numbers and compatibility

When purchasing mud flaps for Nissan Qashqai J10 It is critical to consider the year of manufacture and type of drive. Below are the article numbers of original parts and their analogues:

• 📌 Front left mudguard:
  • Original: 78210-4M000 (for 2WD), 78210-4M001 (for 4WD)
  • Analogue: HEPU 710-10-0141, FEBI 35626
• 📌 Front right mudguard:
  • Original: 78200-4M000 (2WD), 78200-4M001 (4WD)
  • Analogue: HEPU 710-10-0140, MANNOL MN7820
• 📌 Rear mudguards (universal for all trim levels): 78220-4M000 (left), 78221-4M000 (right). Analogues: FEBI 35627, SIDEM 800356.

Important: mudguards for Qashqai J10 not interchangeable with parts for J11 (second generation) due to the changed geometry of the arches. Also pay attention to the packaging: in some versions (for example, Tekna) rear mudguards may have additional mountings for parking sensors.

Step-by-step instructions for installing mud flaps on the Qashqai J10

Installing mudguards does not require special skills, but will require care and a set of tools: a socket wrench 10 mm, a flathead screwdriver, silicone grease for clips and a hair dryer (to soften the plastic in cold weather).

Lift or jack with stops|

Socket wrench set (10mm, 12mm)|

Plastic clip remover|

Silicone grease (eg Liqui Moly Silicone-Spray)|

New clips (if necessary) -->

Step 1. Dismantling old mudguards

1. Raise the car on a lift or place it on a jack, having first secured the wheels with chocks.
2. Remove the wheel from the side where you plan to replace the mudguard.
3. Unscrew the mounting bolts (usually 2-3 pieces per 10 mm) at the bottom of the arch.
4. Carefully pry off the clips with a screwdriver or puller. If the clips are broken, do not try to “pull them out” - this will damage the plastic of the arch.

Step 2. Installing new mudguards

1. Before installation, apply silicone grease to the rubber seals of the new mudguard - this will make the fit easier and prevent squeaks.
2. Start with the top clips, then secure the bottom bolts. Do not tighten them all the way straight away!
3. Make sure the mudguard fits snugly around the entire perimeter of the arch. If there are gaps, bend the plastic with a hairdryer (temperature no higher 60°C).
4. Tighten the bolts crosswise to avoid distortion.

Step 3: Check

After installation, spin the wheel and check whether the mudguard catches on the tire when turning. If noise is heard, loosen the fasteners and adjust the position of the part.

What to do if the mudguard does not fit in place?

If the new mudguard does not fit into the grooves, there are two possible reasons:

1. **Wrong part number** - check compatibility with your equipment (for example, mud flaps for 4WD not suitable for 2WD).

2. **Arch deformation** - often occurs after an accident. In this case, it may be necessary to straighten or install the mudguard with adjustment (trimming of excess plastic).

Top 5 mistakes when choosing and installing mudguards on the J10

Even experienced car owners make mistakes that lead to premature wear of the mudguards or damage to the body. Here are the most common of them:

1. Buying universal mud flaps. Parts “for all models” rarely fit perfectly. For Qashqai J10 It is critical to observe the geometry, otherwise the mudguard will catch on the wheel when turning.
2. Ignoring the condition of the clips. Broken fasteners cause the mudguard to move away from the arch and begin to dangle, losing its protective functions.
3. Installation without lubrication. Without silicone lubricant, rubber seals quickly become tanned, which leads to squeaks and cracks.
4. Bolt tightening. Excessive tightening force deforms the plastic, especially in cold weather.
5. Lack of inspection after installation. Many people forget to spin the wheel and check the clearances, which is why the mudguard rubs against the tire.

⚠️ Attention! If you are installing aluminum mudguards, be sure to treat the fastening areas with an anti-corrosion compound (for example, Dinitrol 4941). Metal parts in contact with the plastic of the arch create a galvanic couple, which accelerates rusting.

Caring for mudguards: how to extend their service life?

Mud flaps on Nissan Qashqai J10 require regular care, especially in winter. Here are the key recommendations:

• 🧼 Washing: Clean the mudguards from dirt and salt at least once every 2 weeks. Use a soft brush and car shampoo without abrasives.
• 🛡️ Protection: Once a season, apply a protective compound to the plastic or rubber (for example, Sonax Plastic Care) to prevent cracking.
• 🔧 Checking fasteners: After severe impacts (for example, hitting a curb), inspect the clips and bolts. Replace broken fasteners immediately.
• 🌡️ Temperature: In cold weather, avoid sudden changes in temperature (for example, do not wash frozen mudguards with hot water).

For polyurethane mudguards, it is useful to treat them once a year silicone grease - this prevents loss of elasticity. It is recommended to coat aluminum parts anti-gravel (For example, Body 930) for protection against corrosion.

Where to buy mud flaps for Nissan Qashqai J10: verified sellers and prices

Prices for mudguards for J10 vary depending on material and brand. Below are current offers from trusted suppliers (as of August 2026):

Seller	Mudguard type	Price (set)	Delivery time	Features
EXIST.ru	Polyurethane (Hepu)	5 800 ₽	1–3 days	1 year warranty, original packaging
EMEX	Original (Nissan)	11 500 ₽	3–5 days	Suitable for all trim levels J10
Autoall	Rubber (budget)	2 900 ₽	2–4 days	No warranty, possible fit inconsistencies
4into	Aluminum (tuning)	22 000 ₽	7–14 days	Individual production to match the body color

When purchasing online, be sure to check with the seller:

• 📋 Compatible with your equipment (2WD/4WD, year of manufacture).
• 📦 All fastening elements included.
• 🔄 Return conditions (many stores do not accept return mudguards if the packaging is opened).

If you are not sure about your choice, contact specialized services such as Nissan-Original or JapanParts — they provide advice on the selection of parts based on the vehicle’s VIN code.

FAQ: Frequently asked questions about mud flaps on the Nissan Qashqai J10

Is it possible to drive without mudguards?

Technically yes, but this greatly reduces the life of the body. Without mudguards, sand, gravel and salt get on the paintwork of arches and sills, which leads to corrosion within 1–2 years. In addition, dirt quickly contaminates the brakes and suspension.

What is the most reliable brand of mud flaps for the J10?

According to test results and owner reviews, the best options are:

• 🥇 Hepu — optimal price/quality ratio, frost resistance.
• 🥈 Febi — hard plastic, precise fit, but a little more expensive.
• 🥉 Mannol - a budget option with good reviews.

Original mud flaps Nissan They lose in durability to polyurethane analogues, but win in precision fit.

Do I need to remove the wheel to replace the mudguard?

For front It is necessary to remove the wheel from the mudguards - otherwise you will not be able to unscrew the lower bolts and get to the clips. For rear you can do without dismantling, but it will be inconvenient to work. If you are inexperienced, it is better to remove the wheel - this will speed up the process and reduce the risk of damage to the plastic.

What to do if the mudguard is cracked, but the fastenings are intact?

Small cracks (up to 5 cm) can be temporarily repaired using:

• 🔥 Soldering plastic (for polyurethane or original parts).
• 🧴 Epoxy glue (For example, 3M Scotch-Weld).
• 🛠️ Fiberglass tapes (to strengthen the seam).

However, this is a temporary solution. Replace the mudguard as soon as possible - the repaired part will not provide full protection.

Will mud flaps from Renault Koleos fit the Qashqai J10?

No, despite the fact that Qashqai J10 And Koleos first generation built on the same platform (Nissan C), their mudguards are different due to differences in the shape of the arches and fastenings. Installation of parts from Renault will require modification, which is impractical.