Sensor 2824A006 for Nissan: original vs analogs, prices and where to buy

If you are faced with the need to replace the sensor 2824A006 in his Nissan, then you probably already know how difficult it is to find accurate information about compatible analogues. This sensor is a frequent guest in engine, ABS or transmission control systems on models from Qashqai to X-Trail, but its original cost may unpleasantly surprise you. In this article we will look at which analogues are suitable instead 2824A006, where to buy them cheaper, and what to look for when choosing.

Let us warn you right away: not all analogues are equally good. Some may only last a few months, while others can surpass the original in reliability. We analyzed car owner reviews, technical specifications and prices to create an honest rating of replacements. And also - prepared FAQ block with answers to the most frequently asked questions about this part.

What is the 2824A006 sensor and where is it used in Nissan

Sensor with article number 2824A006 is a component that is most often found in the following vehicle systems Nissan:

• 🔧 Crankshaft position sensor (on models with engines MR20DD, QR25DE)
• 🚗 Wheel speed sensor (in ABS system for Qashqai J10/J11, X-Trail T31/T32)
• ⚙️ Automatic transmission selector position sensor (on Murano Z51, Pathfinder R51)

The exact purpose depends on the year and model of your vehicle. For example, in Nissan Juke F15 (2010–2014) this part number usually refers to the crankshaft sensor, and in Navara D40 - to the ABS sensor. To avoid mistakes, check the location of the part according to VIN code or in the electronic catalog Nissan EPC.

Important! Some sellers indicate 2824A-006 as a universal article, but in fact it may have modifications depending on the region of production of the car (for example, 2824A-JM00A for the Japanese market).

Original vs analogues: what to choose and why

Original sensor from Nissan with article number 2824A006 will cost on average from 4,500 to 7,800 rubles (price depends on region and dealer markup). But is there any point in overpaying? Let's compare:

Parameter	Original (Nissan)	High-quality analogue	Budget analogue
Service life	100,000–150,000 km	80,000–120,000 km	30,000–50,000 km
Price, rub.	4 500–7 800	1 800–3 500	800–1 500
Warranty	12–24 months	6–12 months	3–6 months
Compatibility	100% (by VIN)	95–99% (needs verification)	70–90% (risk of errors)

High-quality analogues from trusted brands (for example, Denso, Bosch, Hella) are often not inferior to the original, but cost 2–3 times less. But cheap Chinese substitutes (for example, nameless ones with AliExpress) can quickly fail or give false signals to the dashboard.

⚠️ Attention! If you choose analog for the sensor crankshaft, make sure it has the same impedance and frequency response. A discrepancy of even 5–10% can lead to engine malfunctions or errors P0335.

Top 5 proven analogs of 2824A006 for Nissan

We have selected the five most reliable substitutes, which have confirmed their performance on owner forums Nissan (data current for 2026):

1. Denso 550-0101 is the best choice for crankshaft sensor. Compatible with MR20DD, QR25DE. Price: ~2,400 rub.
   • ✅ Exact match to the original in terms of parameters
   • ✅ 12 month warranty
   • ❌ May not be suitable for diesel engines
2. Bosch 0 261 210 047 - universal ABS sensor for Qashqai And X-Trail. Price: ~1,900 rub.
   • ✅ Fits most 2010-2020 models.
   • ✅ Resistant to moisture and temperature changes
   • ❌ Sometimes requires additional configuration after installation
3. Hella 6DT 009 107-021 — premium substitute for automatic transmission selector sensor. Price: ~3,200 rub.
   • ✅ Perfect fit, no play
   • ✅ Compatible with Murano Z51 And Pathfinder R51
   • ❌ High price for analogue
4. Febi Bilstein 28240 - a budget but high-quality option. Price: ~1,500 rub.
   • ✅ Good price/quality ratio
   • ✅ Suitable for Juke And Note
   • ❌ Short warranty period (6 months)
5. Blue Print ADT33103 — optimal for ABS sensors. Price: ~1,700 rub.
   • ✅ Certified for the European market
   • ✅ Easy to install without modifications
   • ❌ May not be suitable for Asian versions Nissan

Critical! If your Nissan equipped with a system ProPILOT or Around View Monitor, use only the original sensor or certified analogues (for example, Denso or Hella). Uncertified parts may cause false alarms in safety systems.

Compare the article number with the EPC database

Make sure it's compatible with your VIN

Check reviews on forums (drive2.ru, nissan-club.ru)

Ask the seller for a quality certificate -->

Where to buy an analogue 2824A006 cheaper: trusted stores

Prices for the same sensor may differ by 2–3 times depending on the place of purchase. We have compiled a rating of reliable suppliers with current prices (as of May 2026):

• 🛒 Exist.ru — original: ~6,200 rub., analogues: from 1,500 rub.
  • ✅ Fast delivery (1–3 days)
  • ✅ Return within 14 days
  • ❌ Prices are higher than those of small sellers
• 🛒 Autodoc.ru — analogues from 1,200 rub.
  • ✅ Frequent discounts (up to 30%)
  • ✅ Large selection of brands
  • ❌ Delivery may take up to 7 days
• 🛒 AliExpress - cheap analogues from 800 rubles.
  • ✅ Lowest prices
  • ❌ Risk of running into a fake
  • ❌ Delivery 2–4 weeks
• 🛒 Local showdowns — used original: 2,000–3,500 rubles.
  • ✅ You can bargain
  • ❌ No guarantee
  • ❌ Risk of buying a faulty part

Advice: If you buy on AliExpress, choose sellers with a rating of at least 98% and a number of orders of 500+. Please pay attention to the photos of the actual product (not stock pictures). It is also useful to order a part with the “Buyer Protection” option - this will allow you to get your money back if it is defective.

How to replace the 2824A006 sensor yourself: step-by-step instructions

Replacing the sensor is not the most difficult procedure, but it requires care. We will look at a universal algorithm for the crankshaft sensor (steps may differ for other types).

Required tools:

• 🔧 Socket set (10 mm, 12 mm)
• 🔧 Ratchet extension
• 🔧 Flat blade screwdriver
• 🔧 Multimeter (for checking)
• 🔧 WD-40 or similar composition

Step by step steps:

1. Disconnect the negative terminal of the battery (required!).
2. Remove the engine protective cover (if equipped).
3. Locate the crankshaft sensor - it is usually located near the flywheel or crankshaft pulley.
4. Disconnect the power connector (carefully pry the lock with a screwdriver).
5. Unscrew the fastening bolt (usually 10 mm).
6. Remove the old sensor and clean the seat from dirt.
7. Install the new sensor, tighten the bolt to torque 8–10 Nm.
8. Connect the connector and check the gap between the sensor and the flywheel (should be 0.5–1.5 mm).
9. Connect the battery and start the engine. Check for errors (eg P0335).

⚠️ Attention! If the engine does not start or runs rough after replacing the crankshaft sensor, check:

• Connector polarity (reversed wires can damage the sensor).
• Gap between sensor and flywheel (too large or small gap will cause errors).
• Wiring integrity (contacts in the connector often oxidize).

What should I do if the Check Engine light comes on after replacing the sensor?

If after installing a new sensor on the dashboard the Check Engine, follow these steps:

1. Connect a diagnostic scanner (for example, ELM327) and read the error code.

2. If there is an error P0335 (crankshaft sensor circuit malfunction), check:

- Quality of contacts in the connector (move the wires with the ignition on).

- Sensor resistance with a multimeter (must be within 500–1000 Ohm).

3. If the error does not clear, try resetting the ECU adaptations (for example, through Nissan Consult or Launch X431).

4. As a last resort, return the old sensor - if the error disappears, the problem is in the new sensor or its installation.

Frequent mistakes when choosing and installing an analogue

Even experienced car owners sometimes make mistakes that lead to repeated replacement of the sensor or breakdown of other components. Here are the most common ones:

1. Buying a sensor without checking the VIN code

   Article 2824A006 may have modifications for different markets (Japan, Europe, USA). For example, a sensor for Nissan Qashqai European assembly may not be suitable for Japanese X-Trail, even if the articles are the same.

2. Ignoring sensor resistance

   For the crankshaft sensor, the resistance should be within 500–1000 Ohm, for ABS sensor - 800–1400 Ohm. Check this parameter with a multimeter before installation!

3. Incorrect bolt torque

   Tightening too loose will result in vibrations and false signals, while tightening too tightly will damage the sensor housing. Optimal moment: 8–12 Nm.

4. Replacing the sensor without cleaning the seat

   Dirt or metal shavings at the installation site may cause a short circuit or incorrect readings. Always clean the surface before installing a new sensor.

5. Using thread sealant

   Many sensors (especially ABS) have an O-ring, and additional sealant can damage it. Use sealant only if specifically stated in the instructions.

Case study: On the forum Drive2 user with nickname @Qashqai_J11 told how after replacing the ABS sensor with a cheap Chinese analogue, the system began to produce false alarms when braking. The reason turned out to be a mismatch in the frequency response of the sensor. I had to buy the original.

FAQ: Answers to frequently asked questions about the 2824A006 sensor

🔍 How to determine that sensor 2824A006 has failed?

Symptoms of malfunction depend on the type of sensor:

• Crankshaft sensor: the engine does not start, the speed fluctuates, error P0335.
• ABS sensor: ABS light is on, wheels lock when braking, errors C1130 or C1145.
• Automatic transmission selector sensor: The box doesn't change gears, it's on Check AT.

For accurate diagnosis, use a scanner (for example, Launch CReader or ELM327).

🛠️ Is it possible to drive with a faulty sensor 2824A006?

Depends on sensor type:

• Crankshaft sensor: No! The engine may stall at any time or run intermittently.
• ABS sensor: It is possible, but the braking distance will increase and the stabilization system will turn off.
• Automatic transmission selector sensor: It is possible, but the gearbox will operate in emergency mode (3rd gear only).

💰 Why do prices for the same sensor differ so much?

The price depends on:

• Brand (original vs analogue).
• Region of purchase (Moscow and St. Petersburg are more expensive than in the regions).
• Seller's markups (dealers) Nissan charge +30–50% to the wholesale price).
• Options (some sensors come with an O-ring, others without).

Tip: compare prices Exist.ru And Autodoc.ru — there are often promotions there.

🔧 Do I need to reset errors after replacing the sensor?

Yes, but not always right away. The algorithm is like this:

1. Install a new sensor.
2. Start the engine and let it run for 5-10 minutes.
3. If the error does not disappear on its own, reset it with the scanner.
4. Drive 10–20 km - some mistakes (for example, P0335) are reset only after movement.

If the error appears again, check the quality of the installation or the sensor itself.

🚗 Will sensor 2824A006 from Nissan fit Renault or Mitsubishi?

Sometimes yes, but not always. Here are known cases of compatibility:

• Renault: sensor may be suitable for Koleos (2010–2016) or Megane III with engine MR20DD.
• Mitsubishi: possible compatibility with Outlander XL (2012–2018) by ABS sensor.
• Infiniti: automatic transmission selector sensor may be suitable for QX50 (2014–2020).

But it's better to check VIN code or catalog EPC, since even within the same model there may be differences.