17 wheels for Nissan Almera G15: complete selection and installation guide

Replacing standard rims with Nissan Almera G15 from 15 or 16 inches to 17-inch - a popular solution among owners seeking to improve the appearance and handling of the car. However, not all R17 wheels are suitable for this model: the wrong choice can lead to friction on the arches, incorrect ABS operation, or even damage to the suspension. In this article we will analyze all technical nuances, from bolt pattern parameters to brand recommendations, and also give step-by-step installation instructions.

Feature Almera G15 (2012–2019) is that the factory R15/16 wheels have modest offsets (ET40–45) and a center hole 66.1 mm. When switching to R17, it is important to consider not only the diameter, but also rim width, departure (ET), as well as compatibility with the braking system. For example, discs with ET below 38 mm may interfere with the calipers, while discs that are too wide (more than 7J) may require the arches to be rolled out. To avoid errors, we analyzed directory data Nissan, reviews from owners and recommendations from tuning studios.

Technical parameters of 17 disks for Nissan Almera G15

Before buying wheels, check their compliance with the key parameters of the car. Main characteristics for Almera G15:

• 🔧 Bolt Pattern (PCD): 4×114.3 - standard for most models Nissan And Renault on the platform B0.
• 📏 Center Hole (DIA): 66.1 mm. Larger diameter discs (eg 67.1mm) will require the use of centering rings.
• ⚖️ Departure (ET): from ET35 to ET45. Optimal range - ET38–42 to maintain controllability.
• 🚗 Rim width: from 6.5J to 7.5J. Width 7J considered universal.
• 🛑 Maximum brake disc diameter: to 280 mm (for front axle). Long overhang discs may interfere with the calipers.

Important: parameters may vary slightly depending on the year of manufacture and configuration. For example, Almera G15 2018 with new generation ABS requires discs with ET≥38, otherwise the sensors will cling to the inner surface of the rim.

Compatibility of 17 wheels with tires: what sizes are suitable

Increasing the diameter of the rims must be accompanied by adjusting the tire size in order to maintain overall wheel diameter (otherwise the speedometer will lie and the suspension will wear out faster). For Almera G15 The following tire sizes are recommended for R17 wheels:

Disc diameter	Disc width	Recommended tire size	Speedometer deviation
R17	6.5J	205/50 R17	+1.2% (insignificant)
R17	7J	215/45 R17	0% (ideal ratio)
R17	7.5J	225/40 R17	-1.5% (speedometer underestimates)

Critical error: using tires with a profile below 40 (for example, 215/35 R17) will lead to a rough ride and the risk of damage to the rims in the pits. Also avoid tires that are too wide (for example, 235/40 R17) - they will require the arches to roll out and increase fuel consumption.

⚠️ Attention: When switching to low profile tires (40–45) be sure to check the pressure - it should be at 0.2–0.3 bar higher than standard (recommended for Almera G15: 2.2 bar front, 2.0 bar rear).

Top 5 models 17 wheels for Nissan Almera G15

Based on reviews from owners and tests by independent experts, we have compiled a rating of the best R17 wheels for Almera G15:

• 🥇 Kosei K1 Racing (Japan) - light forged wheels weighing 6.8 kg, departure ET42. Ideal for a sporty driving style.
• 🥈 Enkei PF05 (Japan) - alloy wheels with optimized geometry to reduce turbulence. Weight 7.2 kg, departure ET38.
• 🥉 BBS CH-R (Germany) - premium wheels with a lifetime guarantee against chips. Departure ET40, width 7J.
• 4️⃣ Replica R17 (OZ Racing) - budget alternative to the original ones OZ. Weight 7.5 kg, require balancing every 10,000 km.
• 5️⃣ LS Wheels Ls-506 (Taiwan) - wheels with aggressive design and offset ET35. Suitable for tuning, but can rub against the calipers on the front axle.

Also note warranty card - from official dealers Enkei And BBS it is only valid when installed in certified centers.

Step-by-step instructions for installing 17 disks on Almera G15

Installing R17 disks on Almera G15 does not require special tools, but it is important to follow the sequence of actions. You will need:

• 🔧 Wheelbrace wrench (or socket on 21 mm).
• 🔩 Jack and stops (for example, Michelin 12V).
• 📏 Torque wrench (optional, but recommended).
• 🧲 Centering rings (if disk DIA > 66.1 mm).

Replacement algorithm:

1. Raise the car with a jack and place jack stands under the rear wheels.
2. Unscrew the bolts securing the old disk (tightening torque - 110 Nm).
3. Remove the disc, clean the hub from rust and dirt (use a wire brush).
4. Install the centering ring (if required) and the new disc, aligning the holes.
5. Hand tighten the bolts, then tighten them in a crisscross pattern with a torque wrench.
6. Lower the car and check the wheel runout (permissible deviation - 0.5 mm).

⚠️ Attention: If after installation a knocking when turningMost likely the disc is hitting the caliper. In this case, you need to increase the offset (buy spacers) or return the old discs.

Common mistakes when selecting and installing 17 disks

Even experienced car owners make mistakes when switching to R17. Let's look at the most common ones:

• 🚫 Ignoring departure (ET). Discs with ET<35 will move the wheel outward, increasing the load on the wheel bearing.
• 🚫 PCD mismatch. Bolt pattern 4×100 (for example, with VW Golf) will not fit - the bolts will not tighten or will come off when moving.
• 🚫 No centering rings. Without them, the disk will “beat” and the bolts will unscrew themselves.
• 🚫 Installing tires that are too wide. Rubber 235/40 R17 The arches will require modification, otherwise it will rub when fully loaded.

What happens if you drive on unbalanced rims?

Vibration on the steering wheel at speeds >80 km/h, uneven tire wear, increased load on the suspension and steering rack.

Another typical problem is hub corrosion after replacing disks. To avoid “sticking” of the disc to the hub, treat the contact surface copper grease (For example, LIQUI MOLY Kupfer-Spray).

Tuning and improvements: what else can be improved with 17 discs

Installing R17 disks is only the first step towards conversion Almera G15. To unlock your vehicle's full potential, consider the following modifications:

• 🔄 Spacers for offset. Allows you to install disks with ET20–30, but require reinforcement of the wheel bearings.
• 🛠️ Rolling out the arches. Required for wider tires 225 mm or disks 8J+.
• 🔧 Replacing shock absorbers. R17 hard drives are better combined with sports racks (for example, KYB Excel-G).
• 🎨 Painting the calipers. Visually emphasizes the new wheels (popular colors: red, yellow, blue).

If you plan to participate in drag racing or drifting, pay attention to forged wheels WedsSport or Volk Racing - they can withstand loads up to 1200 kg on the wheel. However, their price starts from 80 000 ₽ per set.

FAQ: answers to frequently asked questions about 17 disks on Almera G15

❓ Is it possible to install 17 wheels on the Almera G15 without changes to the suspension?

Yes, if the disc offset is within the range ET38–45, and the width does not exceed 7.5J. In this case, modification of the arches or replacement of shock absorbers is not required. However, upon departure ET<35 or width 8J+ rolling may be required.

❓ What tire pressure should be with R17 wheels?

For tires 205/50 R17 or 215/45 R17 recommended pressure: 2.3 bar front and 2.1 bar behind. With a low profile (40) increase the pressure by 0.2 bar to protect disks from deformation.

❓ Will 17 rims affect fuel consumption?

Yes, but only slightly. Increasing the diameter of the rims and reducing the profile of the tires increases rolling resistance. On average, consumption will increase by 0.3–0.5 l/100 km during a quiet ride and up to 1 l/100 km with an aggressive driving style.

❓ Is it possible to install disks with PCD 4×100 on Almera G15?

No! Bolt pattern 4×100 incompatible with 4×114.3. Installing such discs will lead to uneven tightening of the bolts and the risk of them loosening while moving. Only use discs with PCD 4×114.3.

❓ What bolts are needed for 17 discs?

Standard bolts Nissan (article 40520-4M000) are suitable for R17 wheels, but their length must be at least 27 mm. Wheels with spacers will require longer bolts (e.g. 40520-4M025 length 35 mm).